A Better Bathroom
By: Danny Lipford
David and Tiffany England have done a lot of work on their home, but the bathroom still needed some work, so we gave it an inexpensive makeover to improve the look and make it more functional.
Remove Textured Ceiling
Removing a textured popcorn ceiling is a messy job, but it isn’t that difficult if the ceiling hasn’t been painted. If the texture was applied before 1980, have it tested for asbestos first.Start by mixing ¼ cup fabric softener with two gallons of hot water in a pump up sprayer. Cover the floor and walls with plastic before spraying the ceiling with the mixture.
Once the ceiling is thoroughly saturated, use a drywall knife or Homax Popcorn Ceiling Scraper (available at ) to scrape off the texture.
After all the texture has been removed, patch any dings or dents with drywall joint compound, and sand the ceiling smooth before painting.
If the ceiling has been painted, wetting it won’t work, and it will need to either be dry scraped or sanded smooth before repainting.
Always wear an approved dust mask or respirator and eye protection when scraping or sanding dry ceiling texture or drywall. Read Choosing a Respirator or Dust Mask to find out more.
Install Bath Vent Fan
To prevent mold and mildew in the bathroom, we installed a Broan Motion Sensing vent fan with light (model ).
The fan runs continuously at low speed and increases to maximum speed when motion is detected. The fan is also extremely quiet, with the lowest sound rating attainable (0.3 Sones).
To help keep mold and mildew out of a bathroom, spray the shower walls weekly with .
Install Crown Molding
We also dressed up the bathroom by installing crown molding around the ceiling.
To cut crown molding, position the molding upside down and at an angle on the miter saw and set the miter saw to a 45° angle. Cope one end of inside corners to produce a reverse profile of the molding.
Watch our video on How to Cut and Install Crown Molding to find out more.
Hardwood Closet Flooring
To improve the closet, we removed the carpet and installed prefinished ¾” thick hardwood flooring on the plywood subfloor using a pneumatic floor nailer.
Install Accent Tile on Tub Surround
Dark accent tiles were installed to replace the damaged tile left when we removed the sliding glass doors on the tub. After using a carbide tipped grout saw to remove the grout around the tiles, a cold chisel was used to break the tile and remove them.
Watch How to Remove and Replace Tub Surround Tile to find out more.
To refinish a worn tub or change the color, you can use a spray on epoxy coating kit such as .
Install Bathroom Accessories
To finish off the bathroom makeover, we replaced the trim on the tub faucet and installed a brushed nickel . Watch How to Install a Showerhead to find out more.
We also replaced the towel rods and installed a with shelf in the tub. Watch How Install a Grab Bar to find out more.
Other Tips from This Episode
Simple Solutions with Joe Truini:
Updating Brass Door Hinges
To change the finish on plated door hinges from brass to brushed nickel, take off the hinges and use a wire wheel on a bench grinder to remove the brass finish. Spray the hinges with two coats of a clear acrylic finish to prevent rust before reinstalling. (Watch Video)
Best New Products with Jodi Marks:
American Standard Champion Toilet
The American Standard Champion 4 Max Toilet has an EverClean surface, which inhibits the growth of bacteria and mold, and a large trap to reduce clogs. The Champion 4 Max Toilet is available at The Home Depot. (Watch Video)
Ask Danny Lipford:
Tile Flooring Prep
While ceramic tile can be laid directly over a concrete slab, a wood subfloor needs to be covered with cement backer board first. Screw or nail the backer board to the floor, and cover seams with fiberglass tape embedded in thin-set adhesive. (Watch Video)
You May Also Like:
|How to Seal a Tub Drain Hole||Half Time Drill Driver Review||Win Danny & His Crew 2017||Danny's Advice on the Radio|