Five Easy Home Repair Fixes
By: Danny Lipford
We’re making five common repairs to homeowner Michelle Thomas’s house, to put it in good shape again.
Fix #1: Curtain Rod Repair
When hanging curtain rods, it’s best to use a stud finder to locate the wall studs above the window and attach the curtain rods directly into wall studs.
To attach curtain rods to walls where studs aren’t present, drill holes through the drywall and use toggle or molly bolts to attach the curtain rod brackets to the wall.
Read our article on How to Hang Anything on Anything to find out more.
Fix #2: Peeling Ceiling PaintPeeling ceiling paint is usually the result of a roof leak. Start by carefully examining the roof above the leak, paying particular attention to any flashing where the roof meets a wall or around a chimney.
Caulk any cracks or gaps in the roofing or flashing with roof repair caulk or roofing cement, and nail any loose flashing securely down.
Also, be sure to caulk around windows to prevent water from running between the casing and siding.
Once the roof leak has been fixed, scrape off any peeling paint, apply joint compound to level the ceiling, sand the joint compound smooth, prime, and paint.
Fix #3: Running Toilet Repair
A running toilet is usually caused by a faulty fill valve mechanism or a warped flapper valve. If the toilet tank refills periodically when it hasn’t been flushed, the problem can usually be solved by replacing the rubber flapper valve at the bottom of the tank.
If the toilet runs all the time, the problem is either:
- A flapper valve that’s stuck open.
- The water level in the tank is set to high.
- A faulty fill valve mechanism.
To replace a faulty fill valve, start by turning off the water and draining the tank. Next, remove the water supply line and defective fill valve mechanism. Install the new fill valve, reattach the water line, fill the tank, and check to make sure the water level in the tank is below the overflow tube when the tank is full.
Watch our video on How to Repair a Toilet to find out more.
Fix #4: Door Hinge Repair
When a door won’t close properly, the problem is often in the depth of the hinge mortises or loose hinges screws.
If the hinge mortise was cut too deep, remove the hinge, insert a wood shim in the mortise, and reattach the hinge. If the mortise isn’t deep enough, use a hammer and chisel to cut it deeper.
If the hinge screw holes in the door or casing are wallowed out, fill the hole with auto body filler or use longer screws to pull the hinge up tight.
If the door still hits the frame, use a hand or motorized plane or a belt sander to remove excess stock from edge of the door.
To find out more, watch our videos on:
Fix #5: Mailbox RepairOur final fix was to repair a rusty mailbox that didn’t close properly.
The mailbox door had been attached to the inside of the mailbox, rather than the outside. Removing the door and repositioning it, had the mailbox door closing again in no time.
The mailbox was then painted with a rust proofing spray paint to make it look as good as new.
Other Tips from This Episode
Simple Solutions with Joe Truini:
Fixing Squeaky Door Hinges
To stop squeaks in door hinges, use a hammer and nail or nail set to tap the hinge pin out from the bottom. Wipe the pin off with a cotton cloth to remove any dirt, grease, or grime. Sand the hinge pin lightly with medium (120 grit) sandpaper to remove any rust. Apply machine oil to the pin, then tap it back into the hinge. (Watch Video)
Best New Products with Jodi Marks:
Ryobi Ultimate Combo Kit
The Ryobi ONE+ cordless Ultimate Combo Kit is perfect for tackling almost any home improvement project. The kit includes a cordless drill, impact driver, reciprocating saw, circular saw, multi-purpose tool, flashlight, two 18-volt lithium-ion batteries, charger, and carrying case. The Ryobi Ultimate Combo Kit is available at The Home Depot. (Watch Video)
Ask Danny Lipford:
Sagging Gate Repair
To repair a sagging gate, purchase and install an anti-sag gate kit, which comes complete with metal corner brackets, steel cable, and a turnbuckle. Attach the kit diagonally to the top of the hinge side of the gate and bottom of the latch side, then tighten the turnbuckle to remove the sag. (Watch Video)
You May Also Like:
|How to Build Closet Shelving||Build Recessed Wall Cabinet||Tip for Cleaning Under the Refrigerator||Hang Rite Product Review|